Skip to content

Colors not matching imported picture.

asked 54 views

I am currently using the OFFNOVA Immerge DTF CISS with my Epson EcoTank ET-8550 printer and ZoroPrint RIP software. I am experiencing significant color-matching issues between my original designs and the printed transfers.

I have spent considerable time researching and trying different settings to correct the colors, but I have not been able to achieve accurate results. Burnt orange is the color giving me the most trouble right now, consistently printing more red than orange. However, I am concerned that this issue may affect other colors as well.

I would appreciate your recommendations for the correct ICC color profile, ink settings, and any other color-management adjustments specifically recommended for the OFFNOVA Immerge system with the ET-8550.

Is there a recommended ZoroPrint color profile or configuration that will produce the most accurate color reproduction with your inks?

I would greatly appreciate any guidance or documentation you can provide.

Thank you for your time and assistance!

Epson EcoTank ET-8550
Larisa Schafferasked

2 answers

ZoroPrint adminZoroPrint team✓ 1 solutionanswered

Hi Larisa, thanks for the detail. Here's what to check, in order:

  1. Start from a clean baseline. In the colour settings, click ↺ Back to DTF standard. Under Colour management (ICC), make sure the output profile is ZoroPrint DTF, not "None".
  2. Check the file. ZoroPrint reads artwork as sRGB. If the design was saved in Adobe RGB, Display P3 or CMYK (common when exporting from Photoshop or Illustrator), oranges and reds shift. Export it as an sRGB PNG and print again.
  3. Our built-in profile wasn't measured on your setup. It was made on an Epson L1800 with different ink and film, and we use it as the starting point on the ET-8550. If OFFNOVA provides an ICC profile for the ET-8550 with Immerge ink, import it with the + button next to the profile and select it. That's the most accurate option.
  4. Shift the hue with the per-channel ink limits. Orange that prints too red means too much magenta compared with yellow. Under Ink limit per channel, lower M from 70 % to about 60 %, or raise Y from 65 % to about 75 %. Change one at a time and print a small test of the orange each time. These limits apply after the colour profile, so they move the hue directly.
  5. Try another rendering intent. In Expert view, set Rendering intent to Relative colorimetric. Perceptual (the default) compresses all colours a little; Relative keeps colours the printer can reach closer to the file. Avoid Saturation, which pushes reds and oranges further.
  6. Fine-tune with linearisation if needed. Print linearisation strip prints 10–100 % patches per channel. If the magenta patches look heavier than the yellow ones at the same percentage, enter the corrections there.

If it's still off, please post a photo of the print next to the original on screen, plus the file (or the hex value of the orange), and we'll suggest exact numbers.

Gianluca Fioreanswered

I am running a Linux OS and using AcroRip within a VM. I decided to try ZoroPrint; it seemed very promising at first, so I paid for a one-month subscription. After wasting nearly $200 on paper and ink through countless test prints, I still haven't been able to get the colors to match what I see on my screen. I tried various ICC profiles and even created a custom profile by adjusting all the settings using an AI. While the color accuracy gradually improved, I still can't get the colors to look vivid—they always appear dull and undersaturated. Furthermore, the prints consistently come out looking transparent, with insufficient ink coverage for both the white and the colored layers. Additionally, I’ve been unable to resolve the linearization issue; I tried tweaking the correction parameters, but that didn't help either. Solid colors—like white, magenta, or cyan—print fine, but colors such as green or orange come out with visible streaks.

Anyway, I’m tired now; I can’t seem to find any good solutions, so I’ll go back to that prehistoric version of AcroRIP :(
WhatsApp Image 2026-11-14 at 16.55.40
.

  • Hi Gianluca, thanks for the detailed write-up and the photo, and sorry about the film and ink.

    The version on your computer is 0.4.1, from early October. The current one is 0.4.12, and two changes since then target exactly what you describe: a built-in DTF colour profile with our "DTF standard" settings (vivid instead of flat colours), and fuller, even white and colour coverage (no more "transparent" prints).

    Could you try this before any more test prints?

    1. Install 0.4.12 from zoroprint.com/download (if you used the .deb, install the new .deb over it).
    2. In the colour settings, click "Back to DTF standard" and check the profile is "ZoroPrint DTF".
    3. Print one small test with green and orange.

    If the streaks are still there, email hello@zoroprint.com with your printer model, a nozzle check photo and the diagnostics file (Help → Save diagnostics for support), and we'll print your file on our side and come back with exact settings.

    — ZoroPrint admin · ZoroPrint team ·

Your answer